The following was completed by Marcel Equipment:
Upon arrival to our yard, all covers & guards were removed & machine was properly power washed
Visual & operational inspections were completed
Engine oil filter was cut open and checked for contaminates, all clean
Transmission filters were cut open and checked for contaminates, all clean
Hydraulic filters were cut open and checked for contaminates, all clean
All suction screens & magnets were checked for contaminates, all clean
Checked final drive - oil levels good and oils clean
Verified the following pressures to ensure within OEM specs:
Pump drive lube
Brake
Hydraulic pump standby
Transmission pump
Transmission lube
Torque inlet
Torque outlet
Steering
Pilot
Dozer tilt & lift
Accumulator
Engine oil
Fuel
Boost
Stall speed
Installed NEW engine thermostat
Due to leak between flywheel housing & block, engine was removed
Resealed torque converter
Installed NEW front & rear crankshaft seals
Resealed flywheel housing to block
Resealed engine oil pan
Resealed starter
Replaced front crankshaft seal
Removed engine to reseal flywheel housing
Replaced all engine belts with NEW
Installed NEW hard nose pins & bushings
Installed NEW A/C compressor & dryer
Reinstalled engine
Serviced electrical bay
Resealed left side pivot shaft
Installed NEW track cannon seal on right side
Tightened blade steering controls
Checked equalizer bar joints, all tight and take grease
Repaired blade quick drop valve
Resealed powertrain pump
Replaced required lines, hoses and tubes
Replaced 4 washer pumps
Installed NEW wiper motor on right hand door
Cleaned and serviced complete HVAC system
Cleaned heater core and evaporator
Serviced A/C system
REBUILT blade lift cylinder mounting yokes
REBUILT the seat suspension
All required repairs were complete to the blade and shimmed accordingly
Checked all gauges, controls, switches, lights
Completed all required miscellaneous repairs
Checked all grease lines and greased unit
Tested and serviced batteries and connections
All mechanical and cosmetic repairs have been completed
Machine will then be sand blasted, primed, painted and detailed.
Price: $ 0 CAD |
Price: $ 0 USD |
RECONDITIONED CAT D6R XL III WH (2007)UNIT# D8675 MACHINE HOURS: 7925 ECM IDLE HOURS: 1706 | |||
---|---|---|---|
![]() Repair / Condition Report The following was completed by Marcel Equipment: Upon arrival to our yard, all covers & guards were removed & machine was properly power washed Visual & operational inspections were completed Engine oil filter was cut open and checked for contaminates, all clean Transmission filters were cut open and checked for contaminates, all clean Hydraulic filters were cut open and checked for contaminates, all clean All suction screens & magnets were checked for contaminates, all clean Checked final drive - oil levels good and oils clean Verified the following pressures to ensure within OEM specs: Pump drive lube Brake Hydraulic pump standby Transmission pump Transmission lube Torque inlet Torque outlet Steering Pilot Dozer tilt & lift Accumulator Engine oil Fuel Boost Stall speed Installed NEW engine thermostat Due to leak between flywheel housing & block, engine was removed Resealed torque converter Installed NEW front & rear crankshaft seals Resealed flywheel housing to block Resealed engine oil pan Resealed starter Replaced front crankshaft seal Removed engine to reseal flywheel housing Replaced all engine belts with NEW Installed NEW hard nose pins & bushings Installed NEW A/C compressor & dryer Reinstalled engine Serviced electrical bay Resealed left side pivot shaft Installed NEW track cannon seal on right side Tightened blade steering controls Checked equalizer bar joints, all tight and take grease Repaired blade quick drop valve Resealed powertrain pump Replaced required lines, hoses and tubes Replaced 4 washer pumps Installed NEW wiper motor on right hand door Cleaned and serviced complete HVAC system Cleaned heater core and evaporator Serviced A/C system REBUILT blade lift cylinder mounting yokes REBUILT the seat suspension All required repairs were complete to the blade and shimmed accordingly Checked all gauges, controls, switches, lights Completed all required miscellaneous repairs Checked all grease lines and greased unit Tested and serviced batteries and connections All mechanical and cosmetic repairs have been completed Machine will then be sand blasted, primed, painted and detailed. | RECONDITIONED CAT D6R XL III WH
Head Office London, Ontario, Canada |