Upon arrival to our yard, all panels, covers and guards were removed and machine was power washed
Local CAT dealer performed the following:
CAT TA inspection
Completed all pressure tests to ensure within OEM specs
Updated all ECM flash files/software
Serviced machine
Cut open all filters to inspect for contaminates - all clean
Checked all suction screens & magnets - all clean
Replaced complete parking brake assembly
Replaced transmission output speed sensor
Replaced powertrain by-pass sensor
Replaced parking brake pressure sensor
Marcel Equipment then completed the following:
Our own visual and operational inspections were completed
NEW CAT DROP-IN ENGINE installed (existing was not correct arrangement)
Installed REBUILT alternator
Installed REBUILT starter
Installed NEW after cooler
Installed NEW A/C compressor
Replaced engine belts with NEW
Installed NEW idler pullies
Sent out rad to be cleaned and tested
Reassembled rad assembly with all NEW seals & hoses
REBEARING & RESEAL TRANSMISSION
Replaced discs & clutches as required
REBEARING & RESEAL TORQUE CONVERTER
REBEARING & RESEAL TRANSFER CASE
Installed reman transmission cooler
Installed NEW engine and transmission mounts
Resealed rear axle assembly & installed NEW wheel seals
Installed NEW pinion bearing
Set pinion backlash
REBUILT rear axle oscillation
NEW front oscillation trunnion installed
Replaced 2 u-joints with NEW
Installed NEW fuel level assembly
Installed NEW starter relay
Resealed steering cylinders
Installed NEW pins & bearings in steering cylinders
Replaced blade cylinder mounting bushings
Replaced blade mount yoke bearing
Replaced required lines, hoses & tubes
Repaired column tilt assembly
REBUILT throttle pedal
NEW pins & bushings in blade control joystick
Installed NEW wiper motor
Serviced electrical bay
Cleaned and serviced complete HVAC system
Serviced A/C system
Checked all gauges, controls, switches, lights etc
Completed all required repairs
Checked all grease lines and greased unit
Tested and serviced batteries and connections
All mechanical repairs have been completed
Machine will have required cosmetic and welding repairs completed in near future
Machine will then be sand blasted, primed, painted and detailed.
Price: $ 0 CAD |
Price: $ 0 USD |
RECONDITIONED CAT 816F II (2010)UNIT# C3303 MACHINE HOURS: 9100 ECM IDLE HOURS: 3684 | |||
---|---|---|---|
![]() Repair / Condition Report Upon arrival to our yard, all panels, covers and guards were removed and machine was power washed Local CAT dealer performed the following: CAT TA inspection Completed all pressure tests to ensure within OEM specs Updated all ECM flash files/software Serviced machine Cut open all filters to inspect for contaminates - all clean Checked all suction screens & magnets - all clean Replaced complete parking brake assembly Replaced transmission output speed sensor Replaced powertrain by-pass sensor Replaced parking brake pressure sensor Marcel Equipment then completed the following: Our own visual and operational inspections were completed NEW CAT DROP-IN ENGINE installed (existing was not correct arrangement) Installed REBUILT alternator Installed REBUILT starter Installed NEW after cooler Installed NEW A/C compressor Replaced engine belts with NEW Installed NEW idler pullies Sent out rad to be cleaned and tested Reassembled rad assembly with all NEW seals & hoses REBEARING & RESEAL TRANSMISSION Replaced discs & clutches as required REBEARING & RESEAL TORQUE CONVERTER REBEARING & RESEAL TRANSFER CASE Installed reman transmission cooler Installed NEW engine and transmission mounts Resealed rear axle assembly & installed NEW wheel seals Installed NEW pinion bearing Set pinion backlash REBUILT rear axle oscillation NEW front oscillation trunnion installed Replaced 2 u-joints with NEW Installed NEW fuel level assembly Installed NEW starter relay Resealed steering cylinders Installed NEW pins & bearings in steering cylinders Replaced blade cylinder mounting bushings Replaced blade mount yoke bearing Replaced required lines, hoses & tubes Repaired column tilt assembly REBUILT throttle pedal NEW pins & bushings in blade control joystick Installed NEW wiper motor Serviced electrical bay Cleaned and serviced complete HVAC system Serviced A/C system Checked all gauges, controls, switches, lights etc Completed all required repairs Checked all grease lines and greased unit Tested and serviced batteries and connections All mechanical repairs have been completed Machine will have required cosmetic and welding repairs completed in near future Machine will then be sand blasted, primed, painted and detailed.
| RECONDITIONED CAT 816F II
Head Office London, Ontario, Canada |