Ph/txt: 519-686-1123
TF - ph:  800-265-5747
“Doing it right today…to earn your business tomorrow.”

CAT D6T XW VP (2014)  UNIT# D5241

MACHINE HOURS: 5115 ECM IDLE HOURS: 1020
previous arrow
next arrow
previous arrow
next arrow
Repair / Condition Report

The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning the machine;

At 3,012 hours, REBUILT the equalizer bar

At 3,328 hours, resealed all cylinders & installed NEW pins & bearings

At 3,691 hours, installed all NEW pins & bearings in blade assembly & line bored where required

At 4,312 hours, completed engine valve set

At 4,312 hours, installed all NEW fuel injectors

At 4,312 hours, installed NEW water pump

At 4,557 hours, installed NEW a/c compressor & dryer

At 4,658 hours, resealed blade lift cylinders

At 4,659 hours, installed NEW batteries

At 4,659 hours, installed complete NEW HDXL undercarriage

At 4,824 hours, REBUILT torque converter

At 4,824 hours, installed REMAN transmission pump

At 4,824 hours, REBUILT transmission including new modulating valves, planetary gears & wiring harness

At 4,824 hours, REBUILT brake assemblies

At 4,824 hours, installed REMAN transmission cooler

At 4,824 hours, resealed brake control valve

The following was completed by Marcel Equipment:

This machine was stripped & power washed

Hired local CAT dealer to perform the following;

CAT TA1 inspection (no oil samples)

Service emissions system if needed

Perform performance checks- boost, fuel, hydraulic & transmission pressures

Change & cut open all filters to inspect for contaminates

Inspect magnetic plugs/screens & suction screens

Check oils & levels

Update ECM flash files

Check for applicable service letters

The following repairs were completed by Marcel Equipment:

Completed our own visual, operational & mechanical inspections

Installed NEW parking brake switch

Replaced all wiper blades

Installed NEW idler guard wear strips

Resealed blade angle cylinder

Line bored angle cylinder mounting bores on blade

Installed NEW bearing on angle cylinder rod end

Line bored equalizer bar mounting bores on machine

Installed NEW pins & bearings on equalizer bar

DPF & DOC were sent out for cleaning

Replaced DPF temp sensor & ARD head sensor

Installed NEW track cannon seals on both sides

Installed NEW piston on track adjuster & resealed

Serviced batteries, connections & load tested

Serviced & cleaned a/c & heater system

Verified all cab functions & switches

Checked all grease points & greased unit

This unit is now ready to work.

CAT D6T XW VP

Price: $
379000
 CAD
Price: $
283000
 USD
Head Office (Marcel London) London, Ontario, Canada

CAT D6T XW VP (2014) UNIT# D5241

MACHINE HOURS: 5115 ECM IDLE HOURS: 1020
Repair / Condition Report

The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning the machine;

At 3,012 hours, REBUILT the equalizer bar

At 3,328 hours, resealed all cylinders & installed NEW pins & bearings

At 3,691 hours, installed all NEW pins & bearings in blade assembly & line bored where required

At 4,312 hours, completed engine valve set

At 4,312 hours, installed all NEW fuel injectors

At 4,312 hours, installed NEW water pump

At 4,557 hours, installed NEW a/c compressor & dryer

At 4,658 hours, resealed blade lift cylinders

At 4,659 hours, installed NEW batteries

At 4,659 hours, installed complete NEW HDXL undercarriage

At 4,824 hours, REBUILT torque converter

At 4,824 hours, installed REMAN transmission pump

At 4,824 hours, REBUILT transmission including new modulating valves, planetary gears & wiring harness

At 4,824 hours, REBUILT brake assemblies

At 4,824 hours, installed REMAN transmission cooler

At 4,824 hours, resealed brake control valve

The following was completed by Marcel Equipment:

This machine was stripped & power washed

Hired local CAT dealer to perform the following;

CAT TA1 inspection (no oil samples)

Service emissions system if needed

Perform performance checks- boost, fuel, hydraulic & transmission pressures

Change & cut open all filters to inspect for contaminates

Inspect magnetic plugs/screens & suction screens

Check oils & levels

Update ECM flash files

Check for applicable service letters

The following repairs were completed by Marcel Equipment:

Completed our own visual, operational & mechanical inspections

Installed NEW parking brake switch

Replaced all wiper blades

Installed NEW idler guard wear strips

Resealed blade angle cylinder

Line bored angle cylinder mounting bores on blade

Installed NEW bearing on angle cylinder rod end

Line bored equalizer bar mounting bores on machine

Installed NEW pins & bearings on equalizer bar

DPF & DOC were sent out for cleaning

Replaced DPF temp sensor & ARD head sensor

Installed NEW track cannon seals on both sides

Installed NEW piston on track adjuster & resealed

Serviced batteries, connections & load tested

Serviced & cleaned a/c & heater system

Verified all cab functions & switches

Checked all grease points & greased unit

This unit is now ready to work.

CAT D6T XW VP

Price: $
379000
 CAD
Price: $
283000
 USD
Head Office (Marcel London) London, Ontario, Canada
© 2022 · Marcel · Site by Erentzen.com
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram