Ph/txt: 519-686-1123
TF - ph:  800-265-5747
“Doing it right today…to earn your business tomorrow.”

CAT 730 (2011)  UNIT# T2713

MACHINE HOURS: 7546 ECM IDLE HOURS: 4767 LOAD FACTOR: 15%
previous arrow
next arrow
previous arrow
next arrow
Repair / Condition Report

The following are repairs completed by CAT dealer prior to Marcel Equipment owning the machine:

At 2,281 hours, 2,000 hour service was completed

At 3,482 hours, box lift cylinder rod ends had NEW pins & bearings installed

At 3,756 hours, 2,000 hour service with valve set was completed

At 4,797 hours, 1,000 hour service was completed

At 5,601 hours, 2,000 hour service with valve set was completed

At 6,739 hours, 1,000 hour service was completed

The following was completed by Marcel Equipment;

Upon arrival to yard, machine was stripped & power washed

Machine was inspected visually & operationally & tested

Repaired retarder by installing NEW solenoid

Installed NEW bearing on rear A-frame

Installed NEW rod end pins & bearings on box cylinders

Installed NEW pins & bearings on steering cylinders

Installed NEW A/C compressor

Wet around A/C compressor – replaced compressor

Installed NEW duo-cone seals on front axle

Resealed front suspension cylinders

Resealed starter & mounting

REBUILT articulation hitch with all NEW pins, bearings & thrust washers

Adjusted oscillation hitch

Installed NEW coolant temp sensor

Due to leak between transmission & torque, they were removed

Transmission was disassembled & inspected

Resealed transmission complete & replaced required discs & plates

Torque converter was disassembled & inspected

Resealed torque & installed updated gear, bearing & race

With transmission out, installed NEW rear main seal

Replaced any required lines, hoses & tubes on machine

Inspected cab & all cab functions

Completed required cab repairs

The following pressures were taken to ensure within OEM spec;

  • Engine oil pressure
  • Fuel pressure
  • Boost pressure
  • Transmission lube pressure
  • Transmission pump pressure
  • Torque converter inlet & outlet pressures
  • Torque converter lock-up pressure
  • Retarder pressures
  • Hoist pressure
  • Steering pressure
  • Standby brake, hoist, fan pressures
  • Secondary steering  pressures
  • Brake accumulator pressures
  • Brake cut-in & cut-out pressures
  • Brake pressures
  • Pilot pressures

This machine is ready to go to work.

 

CAT 730

Price: $
350000
 CAD
Price: $
273000
 USD
Head Office (Marcel London) London, Ontario, Canada

CAT 730 (2011)UNIT# T2713

MACHINE HOURS: 7546 ECM IDLE HOURS: 4767 LOAD FACTOR: 15%
Repair / Condition Report

The following are repairs completed by CAT dealer prior to Marcel Equipment owning the machine:

At 2,281 hours, 2,000 hour service was completed

At 3,482 hours, box lift cylinder rod ends had NEW pins & bearings installed

At 3,756 hours, 2,000 hour service with valve set was completed

At 4,797 hours, 1,000 hour service was completed

At 5,601 hours, 2,000 hour service with valve set was completed

At 6,739 hours, 1,000 hour service was completed

The following was completed by Marcel Equipment;

Upon arrival to yard, machine was stripped & power washed

Machine was inspected visually & operationally & tested

Repaired retarder by installing NEW solenoid

Installed NEW bearing on rear A-frame

Installed NEW rod end pins & bearings on box cylinders

Installed NEW pins & bearings on steering cylinders

Installed NEW A/C compressor

Wet around A/C compressor – replaced compressor

Installed NEW duo-cone seals on front axle

Resealed front suspension cylinders

Resealed starter & mounting

REBUILT articulation hitch with all NEW pins, bearings & thrust washers

Adjusted oscillation hitch

Installed NEW coolant temp sensor

Due to leak between transmission & torque, they were removed

Transmission was disassembled & inspected

Resealed transmission complete & replaced required discs & plates

Torque converter was disassembled & inspected

Resealed torque & installed updated gear, bearing & race

With transmission out, installed NEW rear main seal

Replaced any required lines, hoses & tubes on machine

Inspected cab & all cab functions

Completed required cab repairs

The following pressures were taken to ensure within OEM spec;

  • Engine oil pressure
  • Fuel pressure
  • Boost pressure
  • Transmission lube pressure
  • Transmission pump pressure
  • Torque converter inlet & outlet pressures
  • Torque converter lock-up pressure
  • Retarder pressures
  • Hoist pressure
  • Steering pressure
  • Standby brake, hoist, fan pressures
  • Secondary steering  pressures
  • Brake accumulator pressures
  • Brake cut-in & cut-out pressures
  • Brake pressures
  • Pilot pressures

This machine is ready to go to work.

 

CAT 730

Price: $
350000
 CAD
Price: $
273000
 USD
Head Office (Marcel London) London, Ontario, Canada
© 2022 · Marcel · Site by Erentzen.com
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram