Ph/txt: 519-686-1123
TF - ph:  800-265-5747
“Doing it right today…to earn your business tomorrow.”

REBUILT / RECONDITIONED CAT 826H (2012)  UNIT# C6925

previous arrow
next arrow
previous arrow
next arrow
Repair / Condition Report

At 7,158 hours, CAT dealer REBUILT the fron differential with NEW crown & pinions

Upon arrival to our yard, machine was stripped for complete power wash

Local CAT dealer was hired to perform the following:

Completed TA inspsection on machine

Performed performance checks

Completed all pressures on machine to ensure within OEM specs

Cut open all filters to inspect for contaminates - all clean except transmission

Transmission filter had some clutch material in it

They inspected all suction screens and magnets

Found some metal (brass) on rear axle magnetic (see notes below)

Found some metal and clutch material on transmission screen (see notes below)

Articulation hitch was inspected and it was good

Due to the hours on the machine & clutch material in trans filter, decision was made to complete a CMCR REBUILD

Machine was shipped to CAT dealer for REBUILD

Machine was rebuilt and reconditioned along side Marcel Equipment

CMCR Rebuild and Reconditioning Information:

Engine was REBUILT to CMCR standards at CAT dealer rebuild facility

Torque converter was REBUILT to CMCR standards at CAT dealer rebuild facility

Transmission was REBUILT to CMCR standards at CAT dealer rebuild facility

Transfer case was REBUILT to CMCR standards at CAT dealer rebuild facility

NEW exhaust wrap was installed on engine

Installed REBUILT starter and alternator

Installed NEW belt tensioner

Installed NEW engine belts

NEW engine and transmission mounts installed

NEW fuel priming pump installed

NEW main chassis harness installed

NEW main engine harness installed

NEW brake and hydraulic control harnesses installed

REBUILT parking brake

Installed NEW parking brake cable

NEW hanger bearing installed

REBUILT drive line slip joint

REBUILT complete drive line with NEW u-joints

Installed NEW pins & bearings for steering cylinders

All hoses in frame were replaced with NEW

Many NEW steel tubes replaced in chassis

All NEW grease lines installed

Drained and cleaned fuel tank

Rad cores were sent out for testing and cleaning

Rad assembly resealed with NEW seals

All cooling assemblies were sent out for testing and cleaning

Resealed main hydraulic control valve

Relay/breaker panel was REBUILT

Resealed transmission filter housing

Changed A/C accumulator, dryer, hoses & connections

Installed NEW fuel sending unit

Installed NEW back-up alarm

All NEW coolant and oils

Machine was commissioned at end with all calibrations and pressure checks completed

Marcel Equipment completed the following work;

Due to metal found on the inspection, rear axle was disassembled

Removed differential and inspected - all good

Checked no-spin - all good

Adjusted back lash on crown & pinion to ensure within spec

Removed planetaries and inspected

Found brass thrust washer failure on left planetary

Resealed both planetaries with NEW duo-cone seals

Cleaned complete axle assembly and reassembled

Installed NEW pinion seal

Inspected axle oscillation group - all good

Cab stripped down to bare frame and reconditioned

NEW cab mounts installed

Serviced and cleaned complete HVAC system

NEW cab pressurizer motor installed

Disassembled & inspected all hydraulic pumps & motors

All pumps & motors were rebuilt as required. Repairs were completed as required

NEW brake / pilot pump installed

Completed all required cosmetic and welding repairs

Repaired blade mount as required and installed NEW pins

All cosmetic and welding repairs have been completed

Complete machine will be sand blasted, primed, painted and NEW decals applied.

 

 

 

 

 

 

 

 

REBUILT / RECONDITIONED CAT 826H

Price: $
0
 CAD
Price: $
0
 USD
Head Office London, Ontario, Canada

REBUILT / RECONDITIONED CAT 826H (2012)UNIT# C6925

Repair / Condition Report

At 7,158 hours, CAT dealer REBUILT the fron differential with NEW crown & pinions

Upon arrival to our yard, machine was stripped for complete power wash

Local CAT dealer was hired to perform the following:

Completed TA inspsection on machine

Performed performance checks

Completed all pressures on machine to ensure within OEM specs

Cut open all filters to inspect for contaminates - all clean except transmission

Transmission filter had some clutch material in it

They inspected all suction screens and magnets

Found some metal (brass) on rear axle magnetic (see notes below)

Found some metal and clutch material on transmission screen (see notes below)

Articulation hitch was inspected and it was good

Due to the hours on the machine & clutch material in trans filter, decision was made to complete a CMCR REBUILD

Machine was shipped to CAT dealer for REBUILD

Machine was rebuilt and reconditioned along side Marcel Equipment

CMCR Rebuild and Reconditioning Information:

Engine was REBUILT to CMCR standards at CAT dealer rebuild facility

Torque converter was REBUILT to CMCR standards at CAT dealer rebuild facility

Transmission was REBUILT to CMCR standards at CAT dealer rebuild facility

Transfer case was REBUILT to CMCR standards at CAT dealer rebuild facility

NEW exhaust wrap was installed on engine

Installed REBUILT starter and alternator

Installed NEW belt tensioner

Installed NEW engine belts

NEW engine and transmission mounts installed

NEW fuel priming pump installed

NEW main chassis harness installed

NEW main engine harness installed

NEW brake and hydraulic control harnesses installed

REBUILT parking brake

Installed NEW parking brake cable

NEW hanger bearing installed

REBUILT drive line slip joint

REBUILT complete drive line with NEW u-joints

Installed NEW pins & bearings for steering cylinders

All hoses in frame were replaced with NEW

Many NEW steel tubes replaced in chassis

All NEW grease lines installed

Drained and cleaned fuel tank

Rad cores were sent out for testing and cleaning

Rad assembly resealed with NEW seals

All cooling assemblies were sent out for testing and cleaning

Resealed main hydraulic control valve

Relay/breaker panel was REBUILT

Resealed transmission filter housing

Changed A/C accumulator, dryer, hoses & connections

Installed NEW fuel sending unit

Installed NEW back-up alarm

All NEW coolant and oils

Machine was commissioned at end with all calibrations and pressure checks completed

Marcel Equipment completed the following work;

Due to metal found on the inspection, rear axle was disassembled

Removed differential and inspected - all good

Checked no-spin - all good

Adjusted back lash on crown & pinion to ensure within spec

Removed planetaries and inspected

Found brass thrust washer failure on left planetary

Resealed both planetaries with NEW duo-cone seals

Cleaned complete axle assembly and reassembled

Installed NEW pinion seal

Inspected axle oscillation group - all good

Cab stripped down to bare frame and reconditioned

NEW cab mounts installed

Serviced and cleaned complete HVAC system

NEW cab pressurizer motor installed

Disassembled & inspected all hydraulic pumps & motors

All pumps & motors were rebuilt as required. Repairs were completed as required

NEW brake / pilot pump installed

Completed all required cosmetic and welding repairs

Repaired blade mount as required and installed NEW pins

All cosmetic and welding repairs have been completed

Complete machine will be sand blasted, primed, painted and NEW decals applied.

 

 

 

 

 

 

 

 

REBUILT / RECONDITIONED CAT 826H

Price: $
0
 CAD
Price: $
0
 USD
Head Office London, Ontario, Canada
© 2022 · Marcel · Site by Erentzen.com
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram