Machine Hours: 10115 - ECM Idle Hours: 3854 - 4841 Neutral Hours

Click the View Video button to view the available video.

CAT D6T XW Waste Handler Crawler Tractor

Price: Call for details
  • Caterpillar C9.3 ACERT Engine
  • Powershift Transmission 
  • Cab (ROPS) with Air Conditioning   
  • Differential Steer
  • 28" Extreme Service Shoes
  • NEW Complete CAT System One Undercarriage Installed at 8625 Hours 
  • Waste Handling Arrangement
  • Final Drive Seal Guards
  • VPAT Blade with Trash Rack
  • Automatic Reversing Fan
  • Rear Striker Bar
  • Ansul Fire Suppression
  • Drawbar Counterweight
  • Front Pull Hook
  • Flood Light Package
  • Lights, Heater, Wipers
  • AM/FM Radio, Amber Safety Light
  • CAT Dealer Maintained Unit
  • Records and Oil Samples are Available
  • Rated at 208 Net HP.
  • Approximately 58,500 LBS.

Repair / Condition Report

CAT Dealer installed NEW complete CAT System One undercarriage at 8625 hours.

CAT Dealer resealed both track adjusters at 8625 hours.

CAT Dealer installed 6 NEW injectors at 8463 hours.

CAT Dealer completed a rebearing and resealing of both final drives at 9995 hours.

Upon arrival to our yard, all covers and guards were removed and unit was powerwashed.

A full visual and operational inspection was completed by Marcel Equipment Limited.

Following is a list of repairs completed by Marcel Equipment Limited at 10115 hours:

Engine oil and filter was changed.

Engine oil filter was cut open and checked for contaminates, it was clean.

Transmission filter was cut open and checked for contaminates, it was clean.

Hydraulic filter was cut open and checked for contaminates, it was clean.

Changed the hydraulic oil.

Installed a NEW seal on the transmission suction screen.

Resealed the transmission pump.

Replaced the scavange pump hose.

Replaced the transmission pressure hose.

Removed and replaced the starter mounting gasket.

Replaced the left angle cylinder hose.

Installed NEW wiper blades.

Installed a NEW windshield washer pump.

Repaired the left door latch.

Repaired the right door lock.

Installed a NEW floor mat.

Checked all grease points and greased unit.

Checked the hard bar and it is good.

REBUILT the C Frame trunnion.

NEW pins and bearings installed on the angle cylinders.

NEW pins and bearings installed on the lift cylinders.

NEW bearings installed on the lift cylinder yokes.

NEW pins and bearing installed on the hard nose.

NEW pins installed on the tilt link.

NEW blade trunnion balls were installed.

NEW pins and bearings installed on the tilt cylinders.

Resealed both track frame cannons.

Repaired the blade float function.

Checked all lights, switches and controls for proper operation.

Checked all pressures, stall speed, etc. and all were within Caterpillar specifications.

Pressure Checks:

Engine Oil Pressure - Specs: 22 PSI - Actual: 37 PSI

Fuel Pressure - Specs: 100-105 PSI - Actual: 105 PSI

Trans Pump Pressure - Specs: 400+-20 PSI - Actual: 391 PSI

Torque Out - Specs: 60+-10 PSI - Actual: 45 PSI

Torque In - Specs: 75+-10 PSI - Actual: 89 PSI

Pilot Pressure - Specs: - Actual: 320 PSI

Implement Pressure - Specs: 3150+- 60 PSI - Actual: 3160 PSI

Stall Speed - Specs: 1575+-30 RPM - Actual: 1564 RPM

Steering Charge Pressure - Specs: 363+-15 PSI - Actual: 360 PSI

Trans Lube Pressure - Specs: 15+-5 PSI - Actual: 24 PSI

This is an excellent ready to work unit.